𝐇𝐁

@halfbreed

475 Following

5028 Followers

𝐇𝐁 pfp

What happened to the Umbreon? Honestly I was working on it with haste at the time….. Which caused a few issues 1. The glue I used didn’t work well causing gaps in between the pieces. 2. My sanding job was horrible 3. I was becoming irritated with the project. So I took a break from it This time I will be welding the parts together with a soldering iron. Projected complete time : Dec 21st. There will be no rush with completion

1 reply

0 recast

3 reactions

𝐇𝐁 pfp

1 reply

0 recast

1 reaction

𝐇𝐁 pfp

Evening Run after Tri/Shoulder gym session

5 replies

2 recasts

7 reactions

𝐇𝐁 pfp

Chill evening jog

8 replies

2 recasts

16 reactions

𝐇𝐁 pfp

Guilty 🍖x2800

1 reply

1 recast

1 reaction

𝐇𝐁 pfp

0 reply

0 recast

1 reaction

𝐇𝐁 pfp

2 replies

0 recast

1 reaction

𝐇𝐁 pfp

3 mile run - first time in a few weeks

25 replies

0 recast

7 reactions

𝐇𝐁 pfp

3D Printed Umbreon Project Used way to much filler on the first layer, lots of sanding to be done still. Placed 2nd layer of filler for the legs and tail. Now I’ll wait 24hrs till cure. Decided on to do the head separately then add on when it’s ready for primer. Will work on it tomorrow Still some imperfections but I think it’s going to come out great

5 replies

2 recasts

12 reactions

𝐇𝐁 pfp

Used about 10 rolls of filament (plastic) but had a few parts reprinted so altogether about $140 - $160 But I still have to sand, fill, sand and paint Total will be around $200 not counting my hours of work.

1 reply

0 recast

0 reaction

𝐇𝐁 pfp

3D Printed Umbreon It’s almost done, 12 more hrs of printing for the ears. Going to start prepping for paint today. Top of the head is about 2 feet tall. Ears will add another 6 inches

9 replies

2 recasts

11 reactions

𝐇𝐁 pfp

Feels longer than 150 days

1 reply

0 recast

0 reaction

𝐇𝐁 pfp

3D Print Umbreon Still have a few more days till the print is finished Reprinting the lower half of legs again. I broke them when trying to connect them together Then sanding, filling and painting *Celcius can for height reference

4 replies

0 recast

8 reactions

𝐇𝐁 pfp

I’m not giving up yet. Attemp #3 - 100 Days of running Day 1 - August 19th, 2024

6 replies

0 recast

8 reactions

𝐇𝐁 pfp

I wish. 😅 Going to give it a try

0 reply

0 recast

0 reaction

𝐇𝐁 pfp

Going to attempt a similar piece after 3D printing umbreon Life size luffy from One Piece maybe 🤔

11 replies

0 recast

10 reactions

𝐇𝐁 pfp

Once it’s done. Should be sick! Might sell it though to cover the costs 😅

1 reply

0 recast

1 reaction

𝐇𝐁 pfp

3D Print UMBREON project update Woke up to spaghetti for the 2nd time 🙃 Restarted the print for the 3rd attempt around 3 am and this time I cut the bigger hind legs in half. Still failed. 11:40 am and the 4th attempt is being started. This time I cut all the legs in half and cut the printing down to two separate plates. Hopefully this time it works

6 replies

0 recast

5 reactions

𝐇𝐁 pfp

Oh wow, my way to dense than. I just accepted that this was supposed to be more than 25% but I see what you’re saying. It’s heavy and thick. That’s what my problem was for one of the legs when printing. It keep getting top heavy and would fall over. Thanks for the recommendation/advice. This is my 6th ever print. First more than 24 hr print

1 reply

0 recast

1 reaction

𝐇𝐁 pfp

Started at 50% then went to 40% I’m gonna have to change again. Going to try 30%. What do you recommend?

1 reply

0 recast

1 reaction